Normally once the above are installed, everything will work fine with my laptop. atkpackage this one is important to activate the keyboard back light network/connectivity (lan, wifi, bluetooth) Ĥ.
I also downloaded all the drivers for my laptop, except Wireless and Bluetooth because there's 3 drivers for both.Īnyone mind helping me in which order I should install these drivers? I'm not sure if I need all of these, but I just downloaded them just incase.Ĭheck your device manager for bluetooth and wifi get the respective hardware id and post it here.Īs for the orders of driver install, i always starts with intel base drivers first, then ASUS, then the others.ģ. Before I do anything, which Windows 8 should I be downloading from here?
PS: Remember to use a program like Magic Jellybean KeyFinder to locate and backup your Windows 8 Serial in case you ever need it. Once you connect to the internet, it will automatically activate. The last 5 digits of the windows serial displayed will be yours. Once installation is complete, check the system properties under the activation status. It will automatically read it off the motherboard and enter it for you.
At no point will it ask your for a serial (if it does, you used the wrong ISO). Windows 7 Loader Slic Activation with OEM Crack Patch Download - How to use the Windows 7 Loader Slic Activation with OEM Information Release 5 to activate Windows 7 Basically it involved 2 stages and here is the stage one: Download 7Loader activator here and extract it using the compression tool to your computer desktop. Here is a post on the digital life forums providing torrents to download the official ISOsĭownload, put them on a DVD/USB then boot and follow along.
Just be sure to use the disc with the version of Win 8 that came with your system (Win 8 Core x86/圆4 or Win 8 Pro x86/圆4) The upside, you can now use any Windows 8 install disc (retail or RTM) to reinstall windows. The SLIC 3.0 gets rid of the Master Serial and instead, takes the serial that use to come on your Genuine Windows sticker, and embeds it in your motherboards firmware.
With the old SLIC 2.0 which used the master serial system, once you got our hands on a OEM Windows install disc, it would automagically work on any other PC made by that OEM. Windows 8 uses the new SLIC 3.0 standard for OEMs to preinstall system with Windows 8. Reboot your PC system to get back into Windows 7.If a system that came with an OEM copy of Windows 8 had a hard drive failure, or you decided to change your disc drive and you need to reinstall Windows, it may be easier to do than you think. Now the Windows 7 bootloader has been removed and rebuilt from scratch.Īt this point, you have a clean and hopefully a fully-working bootloader with one entry for Windows 7.
Now remove the old BCD registry, and create a new one instead.īcdedit.exe /store c:\boot\bcd.tmp /create Replace X in the command line above with the device letter to the CD/DVD drive that is running your Windows 7 Recovery Disk. So, command and its switches must be on the same line. Each command shown below is separated by a newline for display purposes only. If your computer is configured differently, be sure to use the appropriate drive letter here instead. Note: We're assuming that the boot drive is drive C: below. In the Command Prompt window we shall perform a number of commands to create the new BCD file.
We could select the "Startup Repair" to fix the boot problem, but we are assuming that you already tried this option and it did not work. Proceed with the process by choosing "Command Prompt" from this list. On the next window, choose the Windows 7 installation that you'd like to perform the repair on. In the next window, select "Repair your computer" to continue. Assuming you've properly configured your BIOS to boot from CDs/DVDs before hard drives, you should get a prompt asking you to "Press any key to boot from the CD/DVD." Put your Windows 7 DVD in the drive and restart your PC. A backup is essential if things go wrong, when you are making changes to your system. NOTE: Before performing any changes to your system, please make sure you have a backup of system and personal data files. Windows 7 and Vista bootloader file is \bootmgrīcdedit edits a file called BCD, which is located in Windows 7's hidden partition under C:\boot\BCD.We are going to use a system command called BCDedit to re-create the BCD file.īCDedit is a really powerful tool that Windows 7 and Windows Vista uses to manage the boot loader entries.īCDEDIT needs a boot loader file to boot your system.Ī boot loader is a file that contains necessary information that instruct the system how to boot/start an operating system. The following information on creating a clean, fresh BCD file maybe helpful to you.
You have reached the point that all suggestions on startup repair have failed and you may now have to re-create a clean boot configuration data (BCD) file. So your Windows 7 PC System no longer boots and you are getting the ".An error occurred while attempting to read the boot configuration data." system error.